Contents
Greenworks trimmers are a great way to get your lawn looking neat and tidy. But what do you do when the string breaks or gets damaged? This blog post will show you how to replace the string on a Greenworks trimmer quickly and easily.
Checkout this video:
Greenworks Trimmer
If you need to replace the string on your Greenworks trimmer, you’ll first need to remove the old string. To do this, you’ll need to unscrew the bump knob at the bottom of the trimmer. Once the knob is removed, you can pull the old string out of the trimmer. To put the new string in, simply feed it through the trimmer and screw the bump knob back on.
Greenworks trimmer
The Greenworks trimmer is a string trimmer that uses a nylon cord to cut grass and weeds. The cord is attached to the spool on the trimmer head, and as the trimmer is used, the cord wears down and needs to be replaced. Replacing the string on a Greenworks trimmer is a simple process that can be done in just a few minutes.
First, remove the trimmer head from the shaft of the trimmer. To do this, unscrew the knob at the bottom of thetrimmer head until it is loose enough to be removed. Once the head is removed, take out any old string from the spool.
Then, thread new string through the eyelets on the inside of the spool, making sure that the string is wrapped aroundthe spool in a clockwise direction. Once all of the string has been fed through the eyelets, put the trimmer head back onto
the shaft of the trimmer and screw on the knob at the bottom ofthe head until it is tight.
Now you are ready to start trimming again! Be sure to follow these same steps when it comes time to replace yourstring again.
Trimmer
Most Greenworks trimmers use a 0.065” diameter line. If your trimmer came with a spool of 0.065” line, you can use that. Otherwise, you can buy 0.065” line at most hardware stores.
To replace the string on your Greenworks trimmer, follow these steps:
1.Remove the old spool of string from the trimmer.
2.Cut a length of 0.065” diameter line that is about 20 feet long.
3.Thread one end of the line through the eyelet on the spool, and wind it around the spool in a clockwise direction until there is about six inches of line remaining.
4.Pull the end of the line through the hole in the center of the spool, and then pull it tight to secure it in place.
5.Continue winding the line around the spool in a clockwise direction until it is completely wound. Make sure that the line is wound evenly and that there are no gaps between turns.
6.Replace the spool on the trimmer, and you’re ready to go!
Greenworks
Assuming you have a Greenworks trimmer with a bump feed spool, follow these steps to replace the string. You’ll need a new spool of line, which you can purchase at most hardware stores.
1. Unplug the trimmer from the power outlet.
2. Remove the spool cap from the trimmer head by unscrewing it counterclockwise.
3. Unwind any remaining line from the spool. If the line is tangled, cut it away with scissors.
4. Cut off a length of new line that is about 20 feet long.
5. Feed one end of the new line through the eyelet on the spool and then tie it in a knot.
6. Wind the line around the spool in a clockwise direction until there is about 6 inches of line remaining.
7. Pull on the end of the line to remove any slack, then cut off any excess with scissors.
8. Replace the spool cap by screwing it clockwise back onto the trimmer head.
9
String
The Greenworks trimmer uses a nylon string that is 0.080 inches in diameter. The string is wound around a spool inside the trimmer head. To replace the string, you will need to remove the old string and spool it with a new one.
String
If the string on your Greenworks trimmer is worn or damaged, you’ll need to replace it. Here’s how:
1. disconnect the trimmer from the power source.
2. remove the spool by unscrewing the cap and pulling out the spool.
3. wind the new string onto the spool, making sure that it’s wound in the correct direction (consult your owner’s manual if you’re not sure).
4. put the spool back in place and screw on the cap.
5. reconnect the trimmer to the power source and you’re ready to go!
Trimmer string
If the trimmer string on your Greenworks trimmer has run out, you’ll need to replace it. Luckily, this is a relatively easy process that only takes a few minutes. In this guide, we’ll show you how to replace the string on a Greenworks trimmer step-by-step.
First, you’ll need to remove the spool of old string from the trimmer. To do this, simply unscrew the spool cap and pull the spool out. Once the spool is removed, you can discard the old string.
Next, you’ll need to thread the new string through the eyelet on the spool. Start by threading one end of the string through the eyelet from the inside out. Then, wrap the string around the spool a few times until there is about 6 inches of string left. Finally, thread the end of the string through the eyelet from the outside in so that it’s locked in place.
Once the new string is in place, you can screw the spool cap back on and reattach the spool to the trimmer. To do this, simply align the holes on the spool with those onthetrimmer body and push them together until they snap into place. And that’s it! You’ve now successfully replacedthestringon your Greenworks trimmer.
Greenworks trimmer string
The Greenworks trimmer uses a 0.065-inch circumference line. The line is available in a 16-foot spool and can be replaced when it becomes worn or damaged. You will need to replace the entire line, as it cannot be repaired. Follow the steps below to replace the string on your Greenworks trimmer.
1. Turn off the trimmer and unplug it from the power outlet.
2. Remove the spool cap by unscrewing it counterclockwise.
3. Pull out any remaining line from the spool.
4. Cut a length of new line that is slightly longer than the old line, using a pair of scissors.
5. Feed one end of the new line through the eyelet on the spool, then thread it through the second eyelet.
6. Wrap the new line around the spool clockwise until there is no slack in the line. Make sure that the end of the line is secured under the first wraps of line on the spool.
7. Screw on the spool cap clockwise until it is tight
Replacement
The Greenworks trimmer uses a string that is located inside of the spool. The string is what cuts the grass and weeds when the trimmer is turned on. Over time, the string will wear down and will need to be replaced. In this article, we will show you how to replace the string on a Greenworks trimmer.
Replacement
Over time, the string on your Greenworks trimmer will become worn and frayed, making it less effective at cutting grass and weeds. Luckily, it’s easy to replace the string on your Greenworks trimmer. With a few simple tools, you can have your trimmer back up and running in no time.
Tools you’ll need:
-Scissors
-Gloves
-Greenworks trimmer
-Replacement string
Instructions:
1. Cut the damaged string off of the spool using scissors. Be sure to leave enough of the string attached to the spool so that you can easily thread the new string through it.
2. Put on gloves to protect your hands from the sharp edges on the spool.
3. Thread one end of the new string through the eyelet on the spool. If there is no eyelet, you can thread the string through one of the holes in the spool.
4. Wrap the string around the spool until there is about 6 inches of string left.
5. Cut the end of the string at an angle so that it will be easier to thread through the second hole in the spool (or eyelet).
6. Thread the end of the string through hole (or eyelet), then pull it tight so that there is no slack in the line.
7. Trim any excess string, then put your Greenworks trimmer back together and you’re good to go!
Trimmer string replacement
If your Greenworks trimmer is in need of a new string, follow these easy steps to replace it. You’ll need a new spool of trimmer line, which can be purchased at most hardware stores.
1. Open the trimmer head. On most Greenworks trimmers, there is a knob on the top of the head that you can turn to loosen the housing and access the spool inside.
2. Remove the old spool of string. If there is any remaining line on the spool, cut it off with scissors before removing it completely.
3. Install the new spool of string. Be sure to thread the line through the eyelet on the side of the housing before winding it onto the spool.
4. Close up the trimmer head and give thestring a few tugs to make sure it’s properly seated before starting up your trimmer again.
Greenworks trimmer string replacement
If your Greenworks trimmer is in need of a new string, follow the steps below to replace it. You will need a new spool of Greenworks trimmer line.
1. Remove the old spool of string from the trimmer.
2. Cut off a length of the new string that is about twice as long as the old one.
3. Wrap one end of the string around the central post on the spool.
4. Start feeding the string through the eyelet on the side of the trimmer head.
5. Continue feeding the string through until you have about 6 inches (15 cm) left.
6. Wrap this end of the string around the other side of the central post, and pull it tight so that there is no slack in the line.
7. Replace the spool in the trimmer head, and you are ready to go!
